Tel: 01633 - 256067
| Part Number | Model | Description | Picture | |
|---|---|---|---|---|
| SWP2343 | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon & estate | Front stabiliser link bar L&R |
|
|
| SWP2068 | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon | Rear stabiliser link bar L&R |
![]() |
|
| SWP6291 | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon | Front lower arm fitted to the REAR suspension |
|
|
| Jaguar X Type Rear Tyre wear Explanation The rear suspension is adjustable. Whilst not every component is adjustable it's adjustable in camber and toe. When changing SWP6291 Lower Arms eccentric bolts will have to be removed as part of the job & should be adjusted to suit new Lower Arms after fitment, not assume that the new parts are exact substitutes for the old ones. If this isn’t adjusted it will cause tyres to wear on the inner part: |
||||
![]() |
||||
| Adjustment Here | ||||
| SWP6242 | 2.2D, 2.5v6, 3.0v6 Saloon & estate | Front wishbone, REAR hydraulic bush As: C2S39661 S2 |
![]() |
|
| SWP8006 | 2.5v6, 3.0v6 Saloon & estate | Front & rear prop shaft CV joint |
![]() |
|
| CVK60 | 2.5v6, 3.0v6 Saloon & estate | Front & rear prop shaft CV Fast Boot |
![]() |
|
| SWP9203 | 2.2D, 2.5v6, 3.0v6 Saloon & estate | Prop shaft centre bearing |
![]() |
|
| SWP6673K | 2.0,2.2D, 2.5v6, 3.0v6 Saloon & estate![]() |
Rear suspension arm bush kit 2 x kits needed per vehicle Arm that these fit into is: C2S24713 & looks like photo to the left |
![]() |
|
| SWP6679 | 2.0D, 2.0V6, 2.2D, 2.5V6, 3.0V6 Saloon & Estate | Rear anti roll bar bush |
![]() |
|
| SWP6680 | 2.0D, 2.0V6, 2.2D, 2.5V6, 3.0V6 Saloon & Estate | Front anti roll bar bush |
![]() |
|
| SWP6339K | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon & estate FOR BREAKDOWN OF BUSH KIT SEE SWP6339 & SWP6340 BELOW |
Rear trailing arm bush kit. Bushes fit in this arm ![]() |
![]() |
|
| SWP6339 | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon & estate | Rear trailing arm bush |
![]() ![]() |
|
| SWP6340 | 2.0, 2.0d, 2.2d, 2.5, 3.0 saloon & estate | Rear trailing arm bush |
![]() ![]() |
|
| SWP6694 | 2.0 Diesel Please check against measurements shown before buying |
Intercooler to inlet manifold hose Total length [running tape along hose] 390mm [approx] OD & ID bigger end 55mm – ID = 45mm [approx] OD & ID smaller end 45mm – ID 35mm [approx] |
|
|
| SWP6695 | 2.0 Diesel Please check against measurements shown before buying |
Turbo to Intercooler hose Total length [running tape along hose] 310mm [approx] OD & ID bigger end 60mm – ID = 50mm [approx] OD & ID smaller end 48mm – ID 36mm [approx] |
![]() |
|
| SWP564 | Various models: Please check against sizes shown |
“Windows” ABS Ring 32 Teeth 81.8mm Inner Diameter 13mm Wide |
![]() |
|
| SWP6730 | Bushes fit into this arm:
|
Rear suspension, upper control arm bush |
![]() |
|