Tel: 01633 - 256067
| Part Number | Model | Description | Picture |
|---|---|---|---|
| SWP2097 | 1.3i, 1.4i, 1.4TD, 1.6i | Front stabiliser link bar L&R |
|
| SWP6272 | 1.25, 1.3, 1.4, 1.6, 1.6tdci, ST150 | Front top strut mounting L&R |
![]() |
| SWP6272B | 1.25, 1.3, 1.4, 1.6, 1.6tdci, ST150 | Front top strut bearing L&R |
![]() |
| SWP6272K | 1.25, 1.3, 1.4, 1.6, 1.6tdci, ST150 | Front top strut mounting & bearing kit L&R |
![]() |
| SWP5939 | 1.25i, 1.3i, 1.4i | Anti roll bar bush, front 15mm |
![]() |
| SWP112 | All models | Brake calliper guide kit. [Eliminates brake shudder] |
![]() |
| SWP2124K | 1.25, 1.3, 1.4, 1.6, ST150 | Sump plug with rubber seal |
![]() |
| SWP2124W | 1.25, 1.3, 1.4, 1.6, ST150 | Rubber seal for sump plug |
![]() |
| HN21 | 1.25, 1.3. 1.4, 1.4tdci, 1.6 | Rear hub nut L&R |
![]() |
| HN21KIT | 1.25, 1.3. 1.4, 1.4tdci, 1.6 | Rear hub nut & grease cap kit L&R |
![]() |
| SWP2223 | 1.25, 1.3. 1.4, 1.4tdci, 1.6 | Rear hub, grease cap |
![]() |
| SWP428K | 1.25, 1.3. 1.4, 1.4tdci, 1.6 | Mass flywheel bolt kit |
![]() |
| FWP3 | All models | Windscreen washer pump twin outlet |
![]() |
| SWP6689 | All models | Wiring harness to suit FWP3 washer pump |
![]() |
| SWP403/4 | 1.25, 1.3. 1.4, 1.4tdci, 1.6 | Wishbone, pinch bolt & nut |
![]() |
| SWP5958 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump, In-line An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
|
| SWP6345 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump. One straight end, one 90º end An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
|
| SWP6346 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump. Both ends at 90º angle. An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
![]() |
| SWP6701 | 1.4TDCI Please check against sizes shown |
Turbo charger hose Total length [running tape along hose] 310mm [approx] OD & ID bigger end 60mm – ID = 50mm [approx] OD & ID smaller end 55mm – ID 45mm [approx] |
|
| SWP6726 | 1.3, 1.4, 1.4TDCi, 1.6 16v, 1.6TDCi | Driveshaft seal | ![]() |
| SWP9594 | Various models: Please check against photograph & dimensions shown |
Driveshaft centre support bearing: 30mm ID 80mm PCD Outer holes 57mm PCD Inner holes |
![]() |
| SWP6746 | 1.25 ZETEC 28-10-02 – 15-6-12 1.3 DURATEC 8-5-02 – 15-6-12 1.4 DURATEC 30-11-01 – 15-6-12 1.6 ZETEC 30-11-01 – 15-6-12 2.0 ZETEC 15-11-04 – 15-6-12 As: 1135010 |
Oil filler cap |
![]() |
| SWP6748 | Various models: Please check against photograph |
Under body heat shield [exhaust to floor] & noise insulations on bulk head [30mm OD] |
![]() |
| SWP806 | RHD Manual models from 01→ | Pedal rubber set [Clutch & brake] |
![]() |
| SWP6834 | 1.3, 1.4, 1.4TDCI, 1.6, 1.6TDCI | Lower rear engine mounting: As: FEM3565 |
![]() |
| SWP6835 | 1.3, 1.4, 1.4TDCI, 1.6, 1.6TDCI | Upper LH engine mounting: As: FEM3566 |
![]() |