Tel: 01633 - 256067
| Part Number | Model | Description | Picture |
|---|---|---|---|
| SWP1030 | 1.9TDi, 2.0i, 2.3, 2.8i, 2.8i 4x4 | Front stabiliser link bar L&R |
|
| DC48 | 2.0 & 2.3 DOHC 1994 - 06 |
Oil filler cap |
![]() |
| DC22K | 2.0i | Sump plug & washer |
![]() |
| SWP112 | 1.9TDi, 2.0i, 2.3, 2.8i, 2.8i 4x4 | Brake calliper guide kit. [Eliminates brake shudder] |
![]() |
| SWP5981K | 1.9tdi, 2.0i, 2.3, 2.8i | Top strut mounting & bearing, front L&R |
![]() |
| SWP6204 | 2.0, 1.8tdci, 2.0tdci | Twin outlet washer pump. [Parallel pins, oval socket] |
![]() |
| SWP6230 | 1.9tdi, 2.0i, 2.3, 2.8i | Twin outlet washer pump |
![]() |
| SWP6710 | 1.9tdi, 2.0i, 2.3, 2.8i | Wiring harness to suit SWP5986 washer pump | ![]() |
| SWP6315 | 1.9tdi, 2.0i, 2.3, 2.8i | Twin outlet washer pump |
![]() |
| SWP6693 | 1.9tdi, 2.0i, 2.3, 2.8i | Wiring harness to suit SWP6315 washer pump |
![]() |
| SWP9519 | 1.9TDi, 2.0i, 2.8v6 | Inner pod joint “Flower pot” style Seal diameter = 123mm Internal splines on Tri-pod = 34 |
![]() |
| SWP8014 | 1.9TDi, 2.0i, 2.8v6 Excludes 1.9d 90BHP Model | O/S Inner intermediate shaft: Long shaft has 26 male splines. Small stub has 26 female splines & 37 male splines. Seal diameter is 33.4mm |
![]() |
| SWP5958 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump, In-line An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
|
| SWP6345 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump. One straight end, one 90º end An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
|
| SWP6346 | Various Diesel models. Please choose what best suits your vehicle between In-line, One straight end, one 90º end, Both ends at 90º angle | Diesel hand primer pump. Both ends at 90º angle. An arrow shows direction of fuel flow. Pump has a non return valve at one end. Both ends are to suit 8mm fuel pipe |
![]() |
| SWP543 | Various models: Please check against sizes shown |
“Windows” ABS Ring 48 Teeth 78.8mm Inner Diameter 13mm Wide |
![]() |
| SWP9594 | Various models: Please check against photograph & dimensions shown |
Driveshaft centre support bearing: 30mm ID 80mm PCD Outer holes 57mm PCD Inner holes |
![]() |
| SWP6748 | Various models: Please check against photograph |
Under body heat shield [exhaust to floor] & noise insulations on bulk head [30mm OD] |
![]() |